StudentShare
Contact Us
Sign In / Sign Up for FREE
Search
Go to advanced search...
Free

Measurement Of Concrete Workability - Essay Example

Cite this document
Summary
 A writer of an essay "Measurement Of Concrete Workability" discusses the point that concrete workability depends on a number of interacting factors: water content, aggregate type and grading, aggregate/cement ratio, the presence of admixtures, and fineness of cement. …
Download full paper File format: .doc, available for editing
GRAB THE BEST PAPER95.9% of users find it useful
Measurement Of Concrete Workability
Read Text Preview

Extract of sample "Measurement Of Concrete Workability"

Measurement Of Concrete Workability Concrete workability depends on a number of interacting factors: water content, aggregate type and grading, aggregate/cement ratio, presence of admixtures, and fineness of cement. The main factor is the water content of the mix since by simply adding water the inter-particle lubrication is increased. 1. Measure out each of the constituents using the balance provided. Note: Water is more accurately measured by volume (1kg of water is equal to 1 litre). Mix the dry ingredients first and gradually add the water while mixing. Water (kg) 4.97* Cement (kg) 13.2 Fine Aggregate (kg) 18.82 Coarse Aggregate (kg) 25.07 Percentage water content (%) 8.71 % Water/cement ratio 0.3765 Curing condition 1.803 * Water content may be reduced dependant on moisture conditions of fine aggregate Table 1: Concrete mix details (24Litres) Required formulae: 2. Workability Testing: Carry out the following workability tests: Slump test – BS EN 12350-2 • Cone of height = 305mm and base diameter = Slump: true, shear & collapse 203mm with smaller opening (102mm diameter) at the top is placed on a smooth surface. The inside of the mould and the base should be moistened at the beginning of the test. The mould must be firmly held against the base during the entire filling process - this is facilitated by handles or foot-rests brazed to the mould. The mould is filled with concrete in 3 approximately equal depth layers. Each layer is tamped 25 times with a standard 16mm diameter steel rod – when compacting the second and third layer, the rod should just penetrate the underlying layer. The top surface is struck off by means of screeding and rolling motion of the tamping rod. Prior to lifting the mould, the area immediately around the base of the cone should be cleared of concrete, which may have dropped accidentally. The cone is slowly lifted clear of the concrete in 2 – 5 seconds (vertically upwards and without twisting) and the unsupported concrete will slump. The difference in height between the upturned slump cone and the highest point of the concrete is called the slump (noted to the nearest 5 mm). Please clean the apparatus by rinsing with water at the end of the test. Measured slump value (mm) =160 mm 4 Place the reinforcement into the mould and pour the concrete, taking good care to achieve good compaction 5 Consider the following discussion points based on your results observations and further research: a What is the effect of the water content on the workability of concrete? Presence of water improves the workability of the concrete. The volume of water affects the density of the concrete. The more the water content, the greater the workability of the concrete. High contents of water results in higher fluidity and hence better workability. b How does the water/cement ratio and method of curing affect the compressive strength of concrete? An increase in the water/cement ratio decreases the compressive strength of the concrete. Large water/cement ratios increase the fluidity of the mixture and this can even cause the concrete to collapse. The method of curing used also affects the strength of the compressive strength of the mixture. All methods except the air curing method increase the compressive strength. c Why is the characteristic strength rather than mean strength of concrete used to specify structural concrete? Characteristic strength is used since it is normally based on statistical concepts as it is the strength below which no more than 5 % of all the cubes that have been tested from the concrete mixture will fall. It is expected that 95 % of all the cube samples will have strength in excess of the design characteristic strength. 6 Comment on the practicalities of placing concrete into a tightly spaced mould containing reinforcement. How did you achieve good compaction of the concrete placed for your beam? The practicality of placing concrete into a tightly spaced mould containing reinforcement is limited by the process of casting the concrete and the cost of performing this operation. In order to achieve a good compaction, vibration is done on the concrete mix using a screed board vibrator. This removes the air spaces present in the mixture. 7 Sketch the beam, showing the reinforcement and describe what each element within the cage is provided for Section A-A of the beam a Regularly spaced ribs They are not less than half of the clear distance between the ribs nor less than 5 cm. it is designed as continuous beam supported by ribs. The modulus of fracture f the ribs can be computed as: b Topping slab This is not less than 10 cm in width and the depth is not less than the minimum width. The spacing is not more than 15 cm. it is normally characterized by loads and spacing. 1) What is the effect of the water content on the workability of concrete? How can you use your Results to draw conclusions about the mix? The amount of water available in the mix improves the workability of the concrete. The volume of water has a direct effect on the density of the concrete. The greater the content of water, the greater the workability of the concrete. High contents of water usually results in higher fluidity and hence better workability. With a computed water content of 8.71 %, the concrete mix is fairly workable. 2) How does the water/cement ratio and method of curing affect the compressive strength of concrete? An increase in the water/cement ratio decreases the compressive strength of the concrete. Large water/cement ratios increase the fluidity of the mixture and this can even cause the concrete to collapse. The method of curing used also affects the strength of the compressive strength of the mixture. All methods except the air curing method increase the compressive strength 3) Why is the characteristic strength rather than the mean strength of concrete used to specify structural concrete? Characteristic strength is used since it is normally based on statistical concepts as it is the strength below which no more than 5 % of all the cubes that have been tested from the concrete mixture will fall. It is expected that 95 % of all the cube samples will have strength in excess of the design characteristic strength. 4) Comment on the practicalities of placing concrete into a tightly spaced mould containing reinforcements. How did you achieve good compaction of the concrete? The practicality of placing concrete into a tightly spaced mould containing reinforcement is limited by the process of casting the concrete and the cost of performing this operation. In order to achieve a good compaction, vibration is done on the concrete mix using a screed board vibrator. This removes the air spaces present in the mixture. 5) How does the tensile steel reinforcement type affect the steel /concrete bond strength? Reinforcement with steel increases the tensile strength of the bond. Bond stress acts parallel to the bar along the interface and hence the axial force emanating from the reinforcing steel bar generates tangential force which is transferred to the concrete. The bond ensures that there is very minimal slip of the steel bars. 6) Sketch the beam, showing the cracks and identify the cracks types according to the failure mode The type of crack is flexural type. The cracks vary between 0.5 and 1.5 units and it is dependent on the steel area and coverage. The average crack spacing usually decreases with time as a result of shrinkage. The width of the crack is dependent on the steel stress, the diameter of the steel bar and the adjacent spacing of the crack. Concrete Break 1. Sketch of the test apparatus, showing the forces acting on the beam. 2. Sketch showing the nature of failure, together with annotations describing why it failed in this way. The beam failed as a result of an inclined crack propagating in a rapid manner as a result of inadequate shear reinforcement on the beam. 3. Two other modes of failure in an RC beam and under what circumstances that they might occur. a. Shear compression failure: This type of failure may result from crushing of the concrete near the flange of compression of the beam and above the tip of the beam that is under compression. b. Shear tension failure: This type of failure occurs as a result of the longitudinal bars lacking adequate anchorage and diagonal cracks start propagating horizontally. 4. Record the final failure load of the beam and convert this into Kg. If the mass of an average small car is around 1500Kg, comment on how many cars, stacked on top of one another would be required to break the beam. 5. Use your knowledge of elastic and plastic behaviour of materials to describe how the beam behaved when loaded and unloaded in a cyclic fashion. What did you notice about the readings on the deflection dial gauge? When the beam is loaded with and unloaded in a cyclic manner, the deflection recorded on the gauge shifts from minimum to maximum and vice versa. When the beam is under loading, the amount of deflection increases due to the exerted load. The kind of deformation experienced by the beam is elastic in nature. If the load is increased up to a certain limit beyond which the deflection remains permanent, it is referred to as plastic deformation References G.D. TAYLOR , Materials in Construction, 2nd edition, Prentice Hall, 1997. Peter Domone and John Illston, Construction Materials their nature and behaviour, 4th edition, 2010. G.D. Taylor, Materials in Construction principles, practice and performance, Longman, 20 Read More
Tags
Cite this document
  • APA
  • MLA
  • CHICAGO
(“Measurement Of Concrete Workability Essay Example | Topics and Well Written Essays - 1500 words”, n.d.)
Retrieved from https://studentshare.org/engineering-and-construction/1682392-measurement-of-concrete-workability
(Measurement Of Concrete Workability Essay Example | Topics and Well Written Essays - 1500 Words)
https://studentshare.org/engineering-and-construction/1682392-measurement-of-concrete-workability.
“Measurement Of Concrete Workability Essay Example | Topics and Well Written Essays - 1500 Words”, n.d. https://studentshare.org/engineering-and-construction/1682392-measurement-of-concrete-workability.
  • Cited: 0 times

CHECK THESE SAMPLES OF Measurement Of Concrete Workability

Non-Destructive Testing - Magnetic Particle Inspection & Ultrasonic Testing

Non-Destructive Testing, as the name itself suggests, is the product inspection (quality control check) process.... Inspection and test typically include measurements of an output and comparison to specific requirements to determine conformity.... Inspection is performed for a wide variety of purposes, e....
6 Pages (1500 words) Essay

Design, Mobility and Mobile Computing

The fieldwork has emphasized the differences between remote mobility, where users travel over long distances, and local mobility, where users walk around within a fixed set of building.... Based on an in depth study, I conclude that local mobility puts up three requirements for computer support.... hellip; This paper presents results from a research project aiming at developing an architecture supporting local mobility within hospital....
8 Pages (2000 words) Essay

Development of Pre-dried and Blended Lime Mortars for the Ready-Mix Market

For increasing sustainability in business operations, there are four key areas that the building industry needs to improve, which are: energy, materials, waste and pollution.... Hence, a prudent use of natural resources is essential (CIOB, 2007: 3). This paper proposes to present… There is an increasing market for the newly introduced ready mix lime mortar....
10 Pages (2500 words) Essay

Concrete perfomance in fire compared to other building materials

There have been numerous works performed that display this behavior of concrete to high temperatures (Kodur et.... al 1997) and this paper aims to add to the pool of knowledge by comparing the performance of concrete with other building materials such as wood, aluminum and steel.... 2006) The reason why concrete is the prime choice with regards to fire safety standards is because of its resistance and low conduction of heat.... That concrete leads in the said properties will be given evidence in this project....
4 Pages (1000 words) Essay

Benefits and technical challenges for using self compacting concrete

The SCC is very fluid and passes around obstructions to fill all the corners and nooks without the risk of either mortar or any other ingredients of concrete detaching out, and simultaneously ensuring that there are no... Self-Compacting concrete also known as self-levelling concrete or the Self-consolidating concrete describes a concrete with the capability to compact itself purely by the support of its own weight and doesn't necessarily require vibration....
8 Pages (2000 words) Essay

Masonry Brick Production

It comprises of summary table indicating requirements for production to be successful.... In this report, production output of masonry brick is put at 100tones per day (100, 000kg per day). Masonry Brick… The analysis of the company in this report involves daily operations of the organization....
6 Pages (1500 words) Term Paper

The Major Advantage of Series-Mounted Diode

The following research paper is focused on analysis and simulation of various low-power topologies of the RF-DC conversion stage.... The simulation is carried out by the application of OrCad PSPICE as shown in (simulation screenshots) in the simulation section.... hellip; The last couples of decades have been characterized by massive development in a wide range of portable electronic devices like smartphones and wireless sensor networks....
7 Pages (1750 words) Research Paper

Highway Materials, Soils, and Concretes

Objectives Assessment of testing principles for smaller and clearer timber specimens in order to allow for the understanding of timber with regard to their anisotropic nature Analysis of the relationship between strain and stress in materials that are taken into consideration Design of a concrete mix from the given details and information Comparison of the outcomes of the trial concrete mix with the expected on the basis of the provided specifications To carry out research as well as interpretations on particular selected engineering materials Strength test on small clear timber specimens Scope The scope of strength test on a small and clear specimen of timbers included and involved; Determination of a variety of strength as well as other properties that are related to strength in the timber through the performance of the strength test The technique adopted in the testing exercise represented the steps and procedures used in the evaluation of various physical and mechanical properties, ensuring the control of factors such as the moisture content, size of the specimen, rate as well as temperature of the loading....
7 Pages (1750 words) Research Proposal
sponsored ads
We use cookies to create the best experience for you. Keep on browsing if you are OK with that, or find out how to manage cookies.
Contact Us